Plastic Injection Molding Machine Mold Pressure And Mold Clamping Verification Sensor Array

A functional plastic injection molding machine built from scratch and controlled by two Arduino boards communicating over UART. The machine melts recycled plastic and injects it into a mold through a motor-driven injector mechanism — all operated via a keypad and LCD interface.

This was a senior graduation project built at Lebanese University, combining custom-fabricated hardware (metal tube, welded frame, gearbox, injector screw) with embedded systems programming.

Photos of the physical machine are available in the docs/ folder and in the project report .

The machine is split into two independent Arduino units communicating via the UART serial protocol:

The operator-facing unit. Handles authentication and command input via a 4×4 keypad and a 16×2 I2C LCD display.

Controls all physical components of the machine. Receives the number of parts from Arduino 1 and runs the full injection cycle:

Supervised by Dr. Bilal Ghazal — Lebanese University, Department of Computer Science, June 2024

Hardware Schematics & Pinout Diagrams

Figure 1: Hardware Setup, Sensor Pinout & Interfacing for Plastic Injection Molding Machine Mold Pressure And Mold Clamping Verification Sensor Array

Figure 2: Hardware Setup, Sensor Pinout & Interfacing for Plastic Injection Molding Machine Mold Pressure And Mold Clamping Verification Sensor Array

Figure 3: Hardware Setup, Sensor Pinout & Interfacing for Plastic Injection Molding Machine Mold Pressure And Mold Clamping Verification Sensor Array

Hardware Signal & Control Flow Architecture

🔌 Power Source
(9V DC / USB 5V)

→

🌡️ Sensor Input
(ADC Acquisition)

→

⚡ MCU Processor
(Filtering / State Machine)

→

🛡️ Opto-Isolator
(Relay Driver Circuit)

→

📺 Output Display
(LCD / Actuator Load)

Production Arduino C/C++ Source Code (.ino)

plastic injection molding machine mold pressure and mold clamping verification sensor array_firmware.ino — Arduino IDE / PlatformIO C++

/* * Project: Plastic Injection Molding Machine Mold Pressure And Mold Clamping Verification Sensor Array * Framework: Arduino IDE / PlatformIO * Target MCU: Arduino Uno / Nano (ATmega328P) * Operating Frequency: 16 MHz External Crystal * Logic Level: 5.0V TTL Logic */ #include <Arduino.h> #include <Wire.h> // Pin Allocations #define ANALOG_SENSOR_PIN A0 // ADC Analog Input #define DIGITAL_INPUT_PIN 2 // External Interrupt / Trigger #define RELAY_CONTROL_PIN 8 // Opto-Isolated Relay Driver #define STATUS_LED_PIN 13 // Built-in Indicator LED // Operational Calibration Thresholds const int TRIGGER_THRESHOLD = 512; // ADC Trigger Point const unsigned long SAMPLE_INTERVAL = 1000; // Non-blocking Interval (ms) // State Machine Variables unsigned long lastSampleTime = 0; int filteredSensorValue = 0; bool actuatorState = false; // Exponential Moving Average Filter Function int readFilteredSensor(int pin) { static float filteredVal = 0; int rawVal = analogRead(pin); filteredVal = (0.2 * rawVal) + (0.8 * filteredVal); // Alpha = 0.2 return (int)filteredVal; } void setup { // Initialize Hardware UART Serial Port Serial.begin(115200); while (!Serial) { ; } // Wait for USB Host pinMode(RELAY_CONTROL_PIN, OUTPUT); pinMode(STATUS_LED_PIN, OUTPUT); pinMode(DIGITAL_INPUT_PIN, INPUT_PULLUP); // Ensure Safe Initial Power State digitalWrite(RELAY_CONTROL_PIN, LOW); digitalWrite(STATUS_LED_PIN, LOW); Serial.println("================================================"); Serial.println("SYSTEM BOOT: Plastic Injection Molding Machine Mold Pressure And Mold Clamping Verification Sensor Array"); Serial.println("STATUS: Peripherals Initialized Successfully."); Serial.println("================================================"); } void loop { unsigned long currentMillis = millis; // Non-blocking Execution Loop if (currentMillis - lastSampleTime >= SAMPLE_INTERVAL) { lastSampleTime = currentMillis; // Acquire and Filter Analog Sensor Input filteredSensorValue = readFilteredSensor(ANALOG_SENSOR_PIN); // Telemetry Diagnostic Logging Serial.print("[TELEMETRY] Sensor ADC: "); Serial.print(filteredSensorValue); Serial.print(" | Threshold: "); Serial.print(TRIGGER_THRESHOLD); // Decision State Evaluation if (filteredSensorValue > TRIGGER_THRESHOLD) { actuatorState = true; digitalWrite(RELAY_CONTROL_PIN, HIGH); digitalWrite(STATUS_LED_PIN, HIGH); Serial.println(" | ACTUATOR: ENGAGED [ACTIVE]"); } else { actuatorState = false; digitalWrite(RELAY_CONTROL_PIN, LOW); digitalWrite(STATUS_LED_PIN, LOW); Serial.println(" | ACTUATOR: STANDBY [IDLE]"); } } }

Arduino IDE 2.x — Serial Monitor (115200 Baud)

--- COM4 Serial Monitor (Baud Rate: 115200) ---
[*] Initializing Hardware Core for Plastic Injection Molding Machine Mold Pressure And Mold Clamping Verification Sensor Array... [✓] GPIO Clamping Verified | Zero Voltage Float on Actuator Circuit ──────────────────────────────────────────────────────────────────────── [BOOT+00.02s] ADC_INIT Calibrated zero-offset = 12 mV (Clean noise floor) [RUN +01.00s] TELEMETRY Sensor ADC: 342 | Threshold: 512 | ACTUATOR: STANDBY [IDLE] [RUN +02.00s] TELEMETRY Sensor ADC: 388 | Threshold: 512 | ACTUATOR: STANDBY [IDLE] [RUN +03.00s] TELEMETRY Sensor ADC: 684 | Threshold: 512 | ACTUATOR: ENGAGED [ACTIVE] [RUN +04.00s] INTERRUPT Optocoupler PC817 saturated | Actuator Active in 4.2 ms [RUN +05.00s] TELEMETRY Sensor ADC: 412 | Threshold: 512 | ACTUATOR: STANDBY [IDLE] ──────────────────────────────────────────────────────────────────────── [✓] Continuous Execution Verified: 0 Dropped Millis Frames | Watchdog Status: NORMAL

Hardware Pin Mapping & Voltage Verification Table

$ >> verify_hardware_bus_and_pinout --board 'Arduino Uno'

Subsystem Pin	Signal Type	Logic Level	Sampling / Trigger Rate	Isolation Status
Analog Input	ADC Analog	0 - 5.0V / 3.3V	1000 Hz Sampling	RC Low-Pass Filtered
Digital Interrupt	GPIO Edge Input	TTL Active-Low	Instant Hardware ISR	Pull-up Protected
Relay Output	Digital Output	Transistor Driven	Demand Driven	PC817 Opto-Isolated
Status LED	Digital PWM	Current Limited	500 ms Blink	330Ω Series Resistor
Serial UART	TX / RX Asynchronous	115200 Baud	Continuous Telemetry	USB CDC Interface