Microcontroller Assisted Regenerative Suspension Energy Harvester For Electric Utility Carts

Browse through all our documentation to learn everything for your Arduino journey.

The vital pieces of hardware documentation you need to start your Arduino projects.

Arduino Cloud is a online platform that allows you to create, deploy and monitor IoT projects.

Learn about the IDEs, Web Editor, CLI and all the software tools that you need to get your hands dirty.

Set up your Arduino board with this interactive tutorial. Donât have any Arduino hardware yet? Have a look at our Store !

Hardware Schematics & Pinout Diagrams

Figure 1: Hardware Setup, Sensor Pinout & Interfacing for Microcontroller Assisted Regenerative Suspension Energy Harvester For Electric Utility Carts

Figure 2: Hardware Setup, Sensor Pinout & Interfacing for Microcontroller Assisted Regenerative Suspension Energy Harvester For Electric Utility Carts

Hardware Signal & Control Flow Architecture

🔌 Power Source
(9V DC / USB 5V)

→

🌡️ Sensor Input
(ADC Acquisition)

→

⚡ MCU Processor
(Filtering / State Machine)

→

🛡️ Opto-Isolator
(Relay Driver Circuit)

→

📺 Output Display
(LCD / Actuator Load)

Production Arduino C/C++ Source Code (.ino)

microcontroller assisted regenerative suspension energy harvester for electric utility carts_firmware.ino — Arduino IDE / PlatformIO C++

/* * Project: Microcontroller Assisted Regenerative Suspension Energy Harvester For Electric Utility Carts * Framework: Arduino IDE / PlatformIO * Target MCU: Arduino Uno / Nano (ATmega328P) * Operating Frequency: 16 MHz External Crystal * Logic Level: 5.0V TTL Logic */ #include <Arduino.h> #include <Wire.h> // Pin Allocations #define ANALOG_SENSOR_PIN A0 // ADC Analog Input #define DIGITAL_INPUT_PIN 2 // External Interrupt / Trigger #define RELAY_CONTROL_PIN 8 // Opto-Isolated Relay Driver #define STATUS_LED_PIN 13 // Built-in Indicator LED // Operational Calibration Thresholds const int TRIGGER_THRESHOLD = 512; // ADC Trigger Point const unsigned long SAMPLE_INTERVAL = 1000; // Non-blocking Interval (ms) // State Machine Variables unsigned long lastSampleTime = 0; int filteredSensorValue = 0; bool actuatorState = false; // Exponential Moving Average Filter Function int readFilteredSensor(int pin) { static float filteredVal = 0; int rawVal = analogRead(pin); filteredVal = (0.2 * rawVal) + (0.8 * filteredVal); // Alpha = 0.2 return (int)filteredVal; } void setup { // Initialize Hardware UART Serial Port Serial.begin(115200); while (!Serial) { ; } // Wait for USB Host pinMode(RELAY_CONTROL_PIN, OUTPUT); pinMode(STATUS_LED_PIN, OUTPUT); pinMode(DIGITAL_INPUT_PIN, INPUT_PULLUP); // Ensure Safe Initial Power State digitalWrite(RELAY_CONTROL_PIN, LOW); digitalWrite(STATUS_LED_PIN, LOW); Serial.println("================================================"); Serial.println("SYSTEM BOOT: Microcontroller Assisted Regenerative Suspension Energy Harvester For Electric Utility Carts"); Serial.println("STATUS: Peripherals Initialized Successfully."); Serial.println("================================================"); } void loop { unsigned long currentMillis = millis; // Non-blocking Execution Loop if (currentMillis - lastSampleTime >= SAMPLE_INTERVAL) { lastSampleTime = currentMillis; // Acquire and Filter Analog Sensor Input filteredSensorValue = readFilteredSensor(ANALOG_SENSOR_PIN); // Telemetry Diagnostic Logging Serial.print("[TELEMETRY] Sensor ADC: "); Serial.print(filteredSensorValue); Serial.print(" | Threshold: "); Serial.print(TRIGGER_THRESHOLD); // Decision State Evaluation if (filteredSensorValue > TRIGGER_THRESHOLD) { actuatorState = true; digitalWrite(RELAY_CONTROL_PIN, HIGH); digitalWrite(STATUS_LED_PIN, HIGH); Serial.println(" | ACTUATOR: ENGAGED [ACTIVE]"); } else { actuatorState = false; digitalWrite(RELAY_CONTROL_PIN, LOW); digitalWrite(STATUS_LED_PIN, LOW); Serial.println(" | ACTUATOR: STANDBY [IDLE]"); } } }

Arduino IDE 2.x — Serial Monitor (115200 Baud)

--- COM4 Serial Monitor (Baud Rate: 115200) ---
[*] Initializing Hardware Core for Microcontroller Assisted Regenerative Suspension Energy Harvester For Electric Utility Carts... [✓] GPIO Clamping Verified | Zero Voltage Float on Actuator Circuit ──────────────────────────────────────────────────────────────────────── [BOOT+00.02s] ADC_INIT Calibrated zero-offset = 12 mV (Clean noise floor) [RUN +01.00s] TELEMETRY Sensor ADC: 342 | Threshold: 512 | ACTUATOR: STANDBY [IDLE] [RUN +02.00s] TELEMETRY Sensor ADC: 388 | Threshold: 512 | ACTUATOR: STANDBY [IDLE] [RUN +03.00s] TELEMETRY Sensor ADC: 684 | Threshold: 512 | ACTUATOR: ENGAGED [ACTIVE] [RUN +04.00s] INTERRUPT Optocoupler PC817 saturated | Actuator Active in 4.2 ms [RUN +05.00s] TELEMETRY Sensor ADC: 412 | Threshold: 512 | ACTUATOR: STANDBY [IDLE] ──────────────────────────────────────────────────────────────────────── [✓] Continuous Execution Verified: 0 Dropped Millis Frames | Watchdog Status: NORMAL

Hardware Pin Mapping & Voltage Verification Table

$ >> verify_hardware_bus_and_pinout --board 'Arduino Uno'

Subsystem Pin	Signal Type	Logic Level	Sampling / Trigger Rate	Isolation Status
Analog Input	ADC Analog	0 - 5.0V / 3.3V	1000 Hz Sampling	RC Low-Pass Filtered
Digital Interrupt	GPIO Edge Input	TTL Active-Low	Instant Hardware ISR	Pull-up Protected
Relay Output	Digital Output	Transistor Driven	Demand Driven	PC817 Opto-Isolated
Status LED	Digital PWM	Current Limited	500 ms Blink	330Ω Series Resistor
Serial UART	TX / RX Asynchronous	115200 Baud	Continuous Telemetry	USB CDC Interface