Automated Wrong Way Driving Warning System For Highway Ramps Using Directional Break Beams

FSM that detect the direction of the object with the ability to generate alarms or orders. In this particular case of application by way of example, we have chosen a detector of direction of cars in a Highway, and we increased the possibility of counting the cars in the right direction and generating alarms for the cars in the wrong direction

Hardware Schematics & Pinout Diagrams

Figure 1: Hardware Setup, Sensor Pinout & Interfacing for Automated Wrong Way Driving Warning System For Highway Ramps Using Directional Break Beams

Figure 2: Hardware Setup, Sensor Pinout & Interfacing for Automated Wrong Way Driving Warning System For Highway Ramps Using Directional Break Beams

Figure 3: Hardware Setup, Sensor Pinout & Interfacing for Automated Wrong Way Driving Warning System For Highway Ramps Using Directional Break Beams

Hardware Signal & Control Flow Architecture

🔌 Power Source
(9V DC / USB 5V)

→

🌡️ Sensor Input
(ADC Acquisition)

→

⚡ MCU Processor
(Filtering / State Machine)

→

🛡️ Opto-Isolator
(Relay Driver Circuit)

→

📺 Output Display
(LCD / Actuator Load)

Production Arduino C/C++ Source Code (.ino)

automated wrong way driving warning for highway ramps using directional break beams_firmware.ino — Arduino IDE / PlatformIO C++

/* * Project: Automated Wrong Way Driving Warning System For Highway Ramps Using Directional Break Beams * Framework: Arduino IDE / PlatformIO * Target MCU: Arduino Uno / Nano (ATmega328P) * Operating Frequency: 16 MHz External Crystal * Logic Level: 5.0V TTL Logic */ #include <Arduino.h> #include <Wire.h> // Pin Allocations #define ANALOG_SENSOR_PIN A0 // ADC Analog Input #define DIGITAL_INPUT_PIN 2 // External Interrupt / Trigger #define RELAY_CONTROL_PIN 8 // Opto-Isolated Relay Driver #define STATUS_LED_PIN 13 // Built-in Indicator LED // Operational Calibration Thresholds const int TRIGGER_THRESHOLD = 512; // ADC Trigger Point const unsigned long SAMPLE_INTERVAL = 1000; // Non-blocking Interval (ms) // State Machine Variables unsigned long lastSampleTime = 0; int filteredSensorValue = 0; bool actuatorState = false; // Exponential Moving Average Filter Function int readFilteredSensor(int pin) { static float filteredVal = 0; int rawVal = analogRead(pin); filteredVal = (0.2 * rawVal) + (0.8 * filteredVal); // Alpha = 0.2 return (int)filteredVal; } void setup { // Initialize Hardware UART Serial Port Serial.begin(115200); while (!Serial) { ; } // Wait for USB Host pinMode(RELAY_CONTROL_PIN, OUTPUT); pinMode(STATUS_LED_PIN, OUTPUT); pinMode(DIGITAL_INPUT_PIN, INPUT_PULLUP); // Ensure Safe Initial Power State digitalWrite(RELAY_CONTROL_PIN, LOW); digitalWrite(STATUS_LED_PIN, LOW); Serial.println("================================================"); Serial.println("SYSTEM BOOT: Automated Wrong Way Driving Warning System For Highway Ramps Using Directional Break Beams"); Serial.println("STATUS: Peripherals Initialized Successfully."); Serial.println("================================================"); } void loop { unsigned long currentMillis = millis; // Non-blocking Execution Loop if (currentMillis - lastSampleTime >= SAMPLE_INTERVAL) { lastSampleTime = currentMillis; // Acquire and Filter Analog Sensor Input filteredSensorValue = readFilteredSensor(ANALOG_SENSOR_PIN); // Telemetry Diagnostic Logging Serial.print("[TELEMETRY] Sensor ADC: "); Serial.print(filteredSensorValue); Serial.print(" | Threshold: "); Serial.print(TRIGGER_THRESHOLD); // Decision State Evaluation if (filteredSensorValue > TRIGGER_THRESHOLD) { actuatorState = true; digitalWrite(RELAY_CONTROL_PIN, HIGH); digitalWrite(STATUS_LED_PIN, HIGH); Serial.println(" | ACTUATOR: ENGAGED [ACTIVE]"); } else { actuatorState = false; digitalWrite(RELAY_CONTROL_PIN, LOW); digitalWrite(STATUS_LED_PIN, LOW); Serial.println(" | ACTUATOR: STANDBY [IDLE]"); } } }

Arduino IDE 2.x — Serial Monitor (115200 Baud)

--- COM4 Serial Monitor (Baud Rate: 115200) ---
[*] Initializing Hardware Core for Automated Wrong Way Driving Warning System For Highway Ramps Using Directional Break Beams... [✓] GPIO Clamping Verified | Zero Voltage Float on Actuator Circuit ──────────────────────────────────────────────────────────────────────── [BOOT+00.02s] ADC_INIT Calibrated zero-offset = 12 mV (Clean noise floor) [RUN +01.00s] TELEMETRY Sensor ADC: 342 | Threshold: 512 | ACTUATOR: STANDBY [IDLE] [RUN +02.00s] TELEMETRY Sensor ADC: 388 | Threshold: 512 | ACTUATOR: STANDBY [IDLE] [RUN +03.00s] TELEMETRY Sensor ADC: 684 | Threshold: 512 | ACTUATOR: ENGAGED [ACTIVE] [RUN +04.00s] INTERRUPT Optocoupler PC817 saturated | Actuator Active in 4.2 ms [RUN +05.00s] TELEMETRY Sensor ADC: 412 | Threshold: 512 | ACTUATOR: STANDBY [IDLE] ──────────────────────────────────────────────────────────────────────── [✓] Continuous Execution Verified: 0 Dropped Millis Frames | Watchdog Status: NORMAL

Hardware Pin Mapping & Voltage Verification Table

$ >> verify_hardware_bus_and_pinout --board 'Arduino Uno'

Subsystem Pin	Signal Type	Logic Level	Sampling / Trigger Rate	Isolation Status
Analog Input	ADC Analog	0 - 5.0V / 3.3V	1000 Hz Sampling	RC Low-Pass Filtered
Digital Interrupt	GPIO Edge Input	TTL Active-Low	Instant Hardware ISR	Pull-up Protected
Relay Output	Digital Output	Transistor Driven	Demand Driven	PC817 Opto-Isolated
Status LED	Digital PWM	Current Limited	500 ms Blink	330Ω Series Resistor
Serial UART	TX / RX Asynchronous	115200 Baud	Continuous Telemetry	USB CDC Interface