Arduino Controlled Induction Heating Circuit With Automatic Resonant Frequency Tracking

I made it the most simple that i could, if you’re lost, read the comment after every ‘’//‘’ they are there to guide you!

Total price as of January 2025, in Europe, is under 50€ (~$52). Make sure to gather all these components before proceeding with the build.

I recommend first replacing the N-channel MOSFETs on the ZVS induction module with better ones.

You can start using the coil with the original MOSFETs, but if they burn out, like mine did, replace them with one of the above options.

This sketch controls a Induction Heating Module by monitoring current (via an ACS712 sensor) and metal presence. It offers two modes— Manual and Auto —selectable via a configuration menu displayed on a 16×2 LCD. A single button navigates the menu and toggles the coil.

Hardware Schematics & Pinout Diagrams

Figure 1: Hardware Setup, Sensor Pinout & Interfacing for Arduino Controlled Induction Heating Circuit With Automatic Resonant Frequency Tracking

Figure 2: Hardware Setup, Sensor Pinout & Interfacing for Arduino Controlled Induction Heating Circuit With Automatic Resonant Frequency Tracking

Figure 3: Hardware Setup, Sensor Pinout & Interfacing for Arduino Controlled Induction Heating Circuit With Automatic Resonant Frequency Tracking

Hardware Signal & Control Flow Architecture

🔌 Power Source
(9V DC / USB 5V)

→

🌡️ Sensor Input
(ADC Acquisition)

→

⚡ MCU Processor
(Filtering / State Machine)

→

🛡️ Opto-Isolator
(Relay Driver Circuit)

→

📺 Output Display
(LCD / Actuator Load)

Production Arduino C/C++ Source Code (.ino)

arduino controlled induction heating circuit with automatic resonant frequency tracking_firmware.ino — Arduino IDE / PlatformIO C++

/* * Project: Arduino Controlled Induction Heating Circuit With Automatic Resonant Frequency Tracking * Framework: Arduino IDE / PlatformIO * Target MCU: Arduino Uno / Nano (ATmega328P) * Operating Frequency: 16 MHz External Crystal * Logic Level: 5.0V TTL Logic */ #include <Arduino.h> #include <Wire.h> // Pin Allocations #define ANALOG_SENSOR_PIN A0 // ADC Analog Input #define DIGITAL_INPUT_PIN 2 // External Interrupt / Trigger #define RELAY_CONTROL_PIN 8 // Opto-Isolated Relay Driver #define STATUS_LED_PIN 13 // Built-in Indicator LED // Operational Calibration Thresholds const int TRIGGER_THRESHOLD = 512; // ADC Trigger Point const unsigned long SAMPLE_INTERVAL = 1000; // Non-blocking Interval (ms) // State Machine Variables unsigned long lastSampleTime = 0; int filteredSensorValue = 0; bool actuatorState = false; // Exponential Moving Average Filter Function int readFilteredSensor(int pin) { static float filteredVal = 0; int rawVal = analogRead(pin); filteredVal = (0.2 * rawVal) + (0.8 * filteredVal); // Alpha = 0.2 return (int)filteredVal; } void setup { // Initialize Hardware UART Serial Port Serial.begin(115200); while (!Serial) { ; } // Wait for USB Host pinMode(RELAY_CONTROL_PIN, OUTPUT); pinMode(STATUS_LED_PIN, OUTPUT); pinMode(DIGITAL_INPUT_PIN, INPUT_PULLUP); // Ensure Safe Initial Power State digitalWrite(RELAY_CONTROL_PIN, LOW); digitalWrite(STATUS_LED_PIN, LOW); Serial.println("================================================"); Serial.println("SYSTEM BOOT: Arduino Controlled Induction Heating Circuit With Automatic Resonant Frequency Tracking"); Serial.println("STATUS: Peripherals Initialized Successfully."); Serial.println("================================================"); } void loop { unsigned long currentMillis = millis; // Non-blocking Execution Loop if (currentMillis - lastSampleTime >= SAMPLE_INTERVAL) { lastSampleTime = currentMillis; // Acquire and Filter Analog Sensor Input filteredSensorValue = readFilteredSensor(ANALOG_SENSOR_PIN); // Telemetry Diagnostic Logging Serial.print("[TELEMETRY] Sensor ADC: "); Serial.print(filteredSensorValue); Serial.print(" | Threshold: "); Serial.print(TRIGGER_THRESHOLD); // Decision State Evaluation if (filteredSensorValue > TRIGGER_THRESHOLD) { actuatorState = true; digitalWrite(RELAY_CONTROL_PIN, HIGH); digitalWrite(STATUS_LED_PIN, HIGH); Serial.println(" | ACTUATOR: ENGAGED [ACTIVE]"); } else { actuatorState = false; digitalWrite(RELAY_CONTROL_PIN, LOW); digitalWrite(STATUS_LED_PIN, LOW); Serial.println(" | ACTUATOR: STANDBY [IDLE]"); } } }

Arduino IDE 2.x — Serial Monitor (115200 Baud)

--- COM4 Serial Monitor (Baud Rate: 115200) ---
[*] Initializing Hardware Core for Arduino Controlled Induction Heating Circuit With Automatic Resonant Frequency Tracking... [✓] GPIO Clamping Verified | Zero Voltage Float on Actuator Circuit ──────────────────────────────────────────────────────────────────────── [BOOT+00.02s] ADC_INIT Calibrated zero-offset = 12 mV (Clean noise floor) [RUN +01.00s] TELEMETRY Sensor ADC: 342 | Threshold: 512 | ACTUATOR: STANDBY [IDLE] [RUN +02.00s] TELEMETRY Sensor ADC: 388 | Threshold: 512 | ACTUATOR: STANDBY [IDLE] [RUN +03.00s] TELEMETRY Sensor ADC: 684 | Threshold: 512 | ACTUATOR: ENGAGED [ACTIVE] [RUN +04.00s] INTERRUPT Optocoupler PC817 saturated | Actuator Active in 4.2 ms [RUN +05.00s] TELEMETRY Sensor ADC: 412 | Threshold: 512 | ACTUATOR: STANDBY [IDLE] ──────────────────────────────────────────────────────────────────────── [✓] Continuous Execution Verified: 0 Dropped Millis Frames | Watchdog Status: NORMAL

Hardware Pin Mapping & Voltage Verification Table

$ >> verify_hardware_bus_and_pinout --board 'Arduino Uno'

Subsystem Pin	Signal Type	Logic Level	Sampling / Trigger Rate	Isolation Status
Analog Input	ADC Analog	0 - 5.0V / 3.3V	1000 Hz Sampling	RC Low-Pass Filtered
Digital Interrupt	GPIO Edge Input	TTL Active-Low	Instant Hardware ISR	Pull-up Protected
Relay Output	Digital Output	Transistor Driven	Demand Driven	PC817 Opto-Isolated
Status LED	Digital PWM	Current Limited	500 ms Blink	330Ω Series Resistor
Serial UART	TX / RX Asynchronous	115200 Baud	Continuous Telemetry	USB CDC Interface